Contact Us

TEL:0595-22990366

E-mail:heyi-frank@heyitech.com

HEYI Building NO.63-1 Yu Shi Road, Economic and Technologic Development Zone, Quanzhou, Fujian, China

Home > Exhibition > Content
How Alarm System Install
Dec 29, 2018

How Alarm System Install


Panel Operation Instruction (HY-H5)

1. Remote Controller 

   1.1. Enroll Remote Controller

       Under the normal status without alarm event, long press “” button with 3s until heard a short “Di” from panel and address “E1” will be shown in LED, then user can start to enroll remote controller. The current address in LED refers to the current remote controller to be enrolled. If user wants to enroll the next address, please press “” button to the next one. 

  If the current address in LED is flashing, it means the current remote controller has not yet been enrolled and user can press any key of remote controller to enroll. If enrollment succeeded, the panel will prompt a short “Di”, meanwhile address in LED will turn flashing into long bright, it means enrollment of remote controller is successful. If the current address in LED is long bright, it means the current address has been already enrolled. User should delete previous one before re-enrolling.

                   

 Note: If heard a long “Di”, it means the remote controller has already been enrolled.

       8 remote controllers maximum can be enrolled.

 1.2. Delete Remote Controller

   In remote controller enrolling status, press “” button with 3s to delete the existing remote controller. After user heard two short ”Di” from panel and the indicator turned long bright into flashing, deletion is successful. 

 


1.3. Exit Remote Controller Enrollment

    In remote controller enrolling status, short press “” button 3 times to exit.

2. Detector 

  2.1. Enroll Detector

     Under the remote controller enrolling, short press “” button once, then panel enters the detector enrollment. The address in LED refers to the 1st detector of current enrolling zone, and short press “” button to the 2ed detector of this zone, then short press short press “” button to the 3rd detector of this zone. 3 detectors for each zone, so short press “” button again to the 1st detector of the next zone. If user wants to directly enter the 1st detector of next zone, please short press “” button. 

     If the current address is flashing, it means the current detector has not yet been enrolled and user can enable detector to transmit alarm signal to be enrolled. If enrollment succeeded, panel will prompt a short “Di”, meanwhile address in LED will turn flashing into long bright, it means successful enrollment of detector. If the current address in LED is long bright, it means the current address has been already enrolled. User should delete previous one before re-enrolling.


Note: If heard a long “Di”, it means the detector has already been enrolled. 96 detectors maximum can be enrolled.

2.2. Delete Detector

In detector enrolling status, press “” button with 3s to delete the existing detector. After user heard two short ”Di” from panel and the indicator turned long bright into flashing, deletion is successful. 



2.3. Exit Detector Enrollment

   In detector enrolling status, short press “” button 2 times to exit.

3. RFID Card 

3.1. Enroll RFID Card

 Under the detector enrolling status, short press “” button once, then panel enters the RFID card enrollment and LED will show “F1”. The current address in LED refers to the RFID card number to be enrolled. If user wants to enroll the next address, please press “” button to the next one.

    If the current address is flashing, it means the current RFID card has not yet been enrolled and user can swipe card in the swiping area of panel to enroll it. If enrollment succeeded, panel will prompt a short “Di”, meanwhile address in LED will turn flashing into long bright, it means successful enrollment of RFID card. If the current address in LED is long bright, it means the current address has been already enrolled. User should delete previous one before re-enrolling.



Note: If heard a long “Di”, it means the RFID card has already been enrolled. 4 RFID cards maximum can be enrolled.

  3.2. Delete RFID Card

  In RFID card enrolling status, press “” button with 3s to delete the existing RFID card. After user heard two short ”Di” from panel and the indicator turned long bright into flashing, deletion is successful. 

                     


  3.3. Exit RFID Card Enrollment

     In RFID card enrolling status, short press “” button once to exit

4. Record/Playback

  4.1. Record

     In panel normal status without alarm events, long press “” button with 3s. After user heard a short “Di” and LED showed “RE”, it means panel starts to record, at this time user can say the recording content in the front of panel. Press “RE” button or wait for panel automatically to stop recording. The maximum recording is 20s.

                        

4.2. Playback 

     In panel normal status without alarm events, short press “” button, after user heard a short “Di” and LED showed “PL”, it means panel enters playback status. If panel has not yet recorded, panel will prompt a long “Di”.

      

5. One Button Calling 

     In panel normal status without alarm events, long press “” button with 3s, after user heard two short “Di” and LED showed “CA”, it means panel enter calling status, at this time panel will dial the preset number and wait for the other side off-hook, then users can start talking to each other. If the panel prompts a long “Di”, it means panel has not yet been set the calling number or GSM module has not yet been initialized.

                

6. Query of GSM Signal 

     In the successful GSM module initialization status, namely, GSM indicator is long bright, long press “” and “ ” button together with 3s, then user will hear two short “Di” and the LED will show “00-05”, it means GSM module signal level. 0 means no signal and the GSM module normal working needs signal above level 3. User should search a place with strong signal to install the panel.

                        

7. Recovery of Wireless Accessory and RFID Setting 

       

Note: Telephone number to send SMS should be already registered in the programming number by app, or panel has not yet registered any programming number, then operation can succeed.


8. Recovery of Factory Fault


8.1. Keys Operation 

As soon as panel charges the power, press “” button and “” button together within 15s, then factory fault is recovered.


Previous: who to call for alarm system

Next: Where to Install Alarm System